réalisation spectroscope

Design, construction, tuning of spectroscopes
Information and discussion about softwares (telescope remote, autoguiding, acquisition, spectral processing ...)
Sebastien Berriot
Posts: 52
Joined: Fri Aug 19, 2016 7:02 pm

réalisation spectroscope

Post by Sebastien Berriot »

Bonjour,

je souhaite réaliser un spectroscope maison ressemblant au spectro "Bareges" de Christian Buil.

j'ai inséré le plan de mon spectro en pièce jointe.

le télescope est un newton 750mm/150mm avec le foyer un peu à l'intérieur du porte occulaire !!!

par conséquent lors de ma réalisation il faudra que lors de la mise au point le foyer de la lentille collimatrice coïncide avec le foyer du télescope.

D'autre part je ne pourrais pas insérer une fente réglable puisque celle-ci doit se trouver au foyer du télescope.

Ma question est :

Est-ce que ce spectro peut fonctionner correctement sans fente?

Merci
Attachments
image
image
Jean-Pierre Masviel
Posts: 35
Joined: Thu Oct 06, 2011 12:54 pm

Re: réalisation spectroscope

Post by Jean-Pierre Masviel »

Pourquoi ne pas utiliser un glasspath pour corriger le tirage ?
Par exemple:
https://www.pierro-astro.com/materiel-a ... ics_detail
LHIRES III # 24, ALPY 600, Atik 314
http://astrosurf.com/jpmasviel/
Ken Harrison
Posts: 197
Joined: Thu Oct 25, 2012 5:45 am
Location: St Leonards, Australia
Contact:

Re: réalisation spectroscope

Post by Ken Harrison »

Sebastien,
The original design was without an entrance slit. I'm sure it will work well.
The resolution will be limited by the size of the star image at the telescope focus. SimSpec for a 3 arcsec seeing on your scope gives a FWHM size of 11 micron and an estimated R= 3100
Berriot_simspec.JPG
Berriot_simspec.JPG (180.85 KiB) Viewed 6014 times
"Astronomical Spectroscopy - The Final Frontier" - to boldly go where few amateurs have gone before....
"Imaging Sunlight - Using a digital Spectroheliograph" - Springer
http://www.astronomicalspectroscopy.com
Sebastien Berriot
Posts: 52
Joined: Fri Aug 19, 2016 7:02 pm

Re: réalisation spectroscope

Post by Sebastien Berriot »

Merci jean-pierre et ken pour vos réponses,

Merci Jean-Pierre pour le lien. Je ne connaissais pas ce type de lentille. Il y a deux types de lentilles x1,6 ou x2.6. Laquelle me conseilles-tu ?
Je pense que celle de x1,6 conviendra car elle rajoute 65 mm de tirage et l'autre 105 mm.

Merci Ken pour la feuille de calculs et les compléments.

Si je rajoute la lentille, je vais pouvoir y intégrer une fente réglable. Il y a des plans sur le site de Chtistian Buil.
Est-ce que quelqu'un aurait réaliser une fente réglable. Si oui, comment ?

J'ai regardé les prix des fentes réglables sur le net, c'est hors de prix !!!!

Merci
bonne journée
Robin Leadbeater
Posts: 1926
Joined: Mon Sep 26, 2011 4:41 pm
Contact:

Re: réalisation spectroscope

Post by Robin Leadbeater »

It will be much easier to use without a slit. Slit spectrographs like this without a guider so you can view the slit and the surrounding field are very difficult to use. All commercial designs have built in guiders, usually using a slit in a mirror

Cheers
Robin
LHIRES III #29 ATIK314 ALPY 600/200 ATIK428 Star Analyser 100/200 C11 EQ6
http://www.threehillsobservatory.co.uk
Ken Harrison
Posts: 197
Joined: Thu Oct 25, 2012 5:45 am
Location: St Leonards, Australia
Contact:

Re: réalisation spectroscope

Post by Ken Harrison »

Sebastien,
The multiple reflective slit plates used in the Spectra-L200 ( and the current 3D printed LowSpec) are available from Jeulin at a reasonable price.
"Astronomical Spectroscopy - The Final Frontier" - to boldly go where few amateurs have gone before....
"Imaging Sunlight - Using a digital Spectroheliograph" - Springer
http://www.astronomicalspectroscopy.com
Robin Leadbeater
Posts: 1926
Joined: Mon Sep 26, 2011 4:41 pm
Contact:

Re: réalisation spectroscope

Post by Robin Leadbeater »

Robin Leadbeater wrote:It will be much easier to use without a slit.
This similar design of a clasical spectrograph by Christian is slitless for example
http://www.astrosurf.com/buil/us/spe2/hresol.htm

Robin
LHIRES III #29 ATIK314 ALPY 600/200 ATIK428 Star Analyser 100/200 C11 EQ6
http://www.threehillsobservatory.co.uk
Robin Leadbeater
Posts: 1926
Joined: Mon Sep 26, 2011 4:41 pm
Contact:

Re: réalisation spectroscope

Post by Robin Leadbeater »

Ken Harrison wrote:Sebastien,
The multiple reflective slit plates used in the Spectra-L200 ( and the current 3D printed LowSpec) are available from Jeulin at a reasonable price.
Hi Ken,

Do you have a contact at Jeulin? Someone on Cloudy Nights is having a problem ordering through their website.

Thanks
Robin
LHIRES III #29 ATIK314 ALPY 600/200 ATIK428 Star Analyser 100/200 C11 EQ6
http://www.threehillsobservatory.co.uk
Sebastien Berriot
Posts: 52
Joined: Fri Aug 19, 2016 7:02 pm

Re: réalisation spectroscope

Post by Sebastien Berriot »

Thank you very much Robin for your advice ;)
Ken Harrison
Posts: 197
Joined: Thu Oct 25, 2012 5:45 am
Location: St Leonards, Australia
Contact:

Re: réalisation spectroscope

Post by Ken Harrison »

Robin, et al,
My contact was fanny.georget@jeulin.fr she was very helpful......

Ken
"Astronomical Spectroscopy - The Final Frontier" - to boldly go where few amateurs have gone before....
"Imaging Sunlight - Using a digital Spectroheliograph" - Springer
http://www.astronomicalspectroscopy.com
Post Reply